Showing results: 451 - 465 of 627 items found.
-
PIC32MX795 Development Board -
SparkFun Electronics
The new version of the UBW32 now uses the PIC32MX795 IC. Based on the work of Brian Schmalz, the UBW32 is a small development board for the new PIC32MX795 32-bit CPU from Microchip. The UBW32 is breadboard friendly and includes all of the external circuitry needed to get the PIC32 up and running. Power can be provided over USB or from an external source. It has three push buttons (Reset, and two user-defined buttons) and five LEDs (Power, USB, and three user defined LEDs). All of the 78(!) of the PIC32's I/O pins are broken out. The board comes pre-loaded with a USB bootloader and special UBW firmware that accepts simple serial commands to control the various I/O functions.
-
NI
The Controller for FlexRIO is optimized for field deployment and offers reliable, extended operation for applications requiring advanced I/O capability and embedded signal processing. It includes a Kintex-7 FPGA, 2 GB of onboard DDR3 DRAM, high-speed serial ports for streaming, and a dual‐core ARM Cortex‐A9 processor running NI Linux Real‐Time for headless operation.The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
FMC667 -
Sundance Multiprocessor Technology Ltd.
The FMC667 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6678 device. The FMC667 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces. Several Gigabit differential pairs from the FMC connector are used to implement a PCIe and Serial Rapid IO interface between the FMC and the carrier.
-
DS-MPE-SER4OPT -
Diamond Systems Corp
The DS-MPE-SER4OPT offers 4 RS-232/RS-485 opto-isolated serial ports in a PCIe MiniCard form factor. Each port offers 16C550 compatibility and ultra-deep 256-byte TX/RX FIFOs. Maximum data rates are 1Mbps in RS-232 mode and 10Mbps in RS-485 mode. The board is available preconfigured for 4 RS-232 ports, 4 RS-485 ports, or a combination of 2 RS-232 and 2 RS-485 ports. I/O signals are provided on two miniature latching connectors, with 2 ports per connector.
-
VXI-5502 -
ICS Electronics
* VXI-5502 has a Sea-of-holes Prototyping Board with multiple power and ground planes for analog and digital prototyping applications.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Acces I/O Products, Inc.
Many types of external computer equipment have a serial ports to communicate with host PCs. ACCES I/O has Communication Cards for all of the popular protocols you may find on this type of equipment (RS-232, RS-422 and RS-485), ranging from a single port to eight ports on a single card. There are also optically isolated versions of some of these cards to ensure effective data transmission on long communication lines, even in electrically noisy environments. Having optical isolation is like having data insurance.
-
Model 6003 -
Pentek, Inc.
- Unique QuartzXM eXpress Module enables deployment in custom form factors- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- Measuring only 2.5 by 4 inches- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- GTY connections for gigabit serial communication- Ruggedized and conduction-cooled versions available- Includes a complete suite of IP functions and example applications- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products
-
EPC-R6410 -
Advantech Co. Ltd.
EPC-R6410 is the RISC based box computer which integrated NXP i.MX6D/Q Cortex-A9 1.0GHz high performance processor. It is designed for the applications that require high performance and rich I/O but low power consumption. It supports dual display via HDMI and VGA up to 1080p, 1 Gigabit Ethernet, 6 USB 2.0 and 4 serials, as well as mini-PCIE for 4G/3G and M.2 for WiFi/BT. With wall mount brackets, fanless and dust-proof design, you can easy install in rugged environment.
-
ELMA Electronic, Inc.
Carriers and adapters enable the use of PMCs or XMCs in a PCI based system. Designed to improve your system with additional I/Os. Key control signals on PCI fixed to ground to reduce signal undershoot. Carrier and adapter allowing you customization of your system platform with additional I/O mezzanine boards for your application needs. A 5 V to 3.3 V linear regulator provided. Carriers and adapters are available for different topologies like CompactPCI, CompactPCI Serial, OpenVPX, VME or VME64x.
-
cPCI-R6002 Series -
ADLINK Technology Inc.
The cPCI-R6002 Series is a 6U CompactPCI rear transition module (RTM) in single/dual slot width (4/8HP) form factor featuring rich IO interfaces. The single slot cPCI-R6002 supports 2x GbE, 2x USB 2.0, 1x DB-9 COM, and 1x DVI-I on the rear panel. The dual slot cPCI-R6002D supports 2x GbE, 4x USB 2.0, 1x DB-9 COM, 1xDVI-I, PS/2 KB/MS, and audio ports on the rear panel. For storage, the cPCI-R6002 provides 2x 7-pin SATA connectors and the cPCI-R6002D offers an additional 2.5" SATA drive space via daughter board. Onboard IO includes 1x 5-pin USB pin header and 1x 10-pin serial TX/RX pin header.
-
Model 54821 -
Pentek, Inc.
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Exceptional dynamic range/analog signal integrity- Xilinx® Kintex® UltraScale" FPGA- Compatible with several VITA standards including: VITA 66.5, VITA 67.2 and VITA 67.3C- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of 2400 DDR4 SDRAM- Programmable frequency synthesizedsample clock generator- Sample clock synchronization to an external system reference- Powerful DMA controllers for moving data- PCI Express (Gen. 1, 2 & 3) interface up to x8- Multi-channel synchronization with clock/sync bus- Optional clock/sync generator for multi-board systems- Optional gigabit serial links for custom FPGA I/O- Optional LVDS port and gigabit serial links for custom FPGA I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Model 2307 -
ICS Electronics
* 2307 Board provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Board. * DE-9 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * Runs on 5 Vdc power.
-
Model 6001 -
Pentek, Inc.
- Now available in RFSoC Gen 3 with the Model 6003- Unique QuartzXM eXpress Module enables deployment in custom form factors- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- Measuring only 2.5 by 4 inches- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- GTY connections for gigabit serial communication- Ruggedized and conduction-cooled versions available- Includes a complete suite of IP functions and example applications- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products
-
196275-01 -
NI
The SHC68-C68-D4, 1m, Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
781293-01 -
NI
The SHC68-C68-D4, 2m, Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
